Control your complex installations safely and easily with our InteliSys NTC Basebox controller, ensuring greater safety, easy communication, and minimal downtime.

The InteliSys NTC Basebox offers: 
 

• AirGateComAp’s controllers incorporate AirGate connection technology to make access to the internet as simple as possible. AirGate enables our controllers to connect to the internet using the existing network infrastructure, negotiating firewalls and VPN systems and removing the requirement for static and public IP addresses. for easy connection to your equipment remotely, without worrying about your asset’s IP address
• Built-in PLCComAp has integrated Programable Logic Controller tightly with our standard line of controllers. This helps our customers to cut costs, minimise points of failure for advanced systems, and overcome any challenge that may occur. interpreter helping with the use of ComAp's free PLC Editor 
• User-defined protections and setpoints on top of default protection
• Controller redundancyRedundancy in critical backup power systems is essential to ensure that the power is never compromised. Our controllers allow for installing a second controller to continuously monitor for potential failure. minimising solution downtime and ensuring the power isn’t compromised 
• More precise measuring with a True Root Mean Square measurement feature 
• Remote control and monitoring of your gen-set operations with WebSupervisor, our cloud-based fleet management tool 
• Compatible load/Var sharing and power management with other ComAp solutions 
• DROOP regulation allowing load and Var sharing when the inter-controller’s communication is lost
• Start-up synchronisationComAp’s Start-up synchronisation eliminates any blackout time, and the start-up time is the same for sites running 2, 10, or even 30 gen-sets. To avoid delaying availability of the system due to slow-starting generators or other problems, any engines that fail to reach running speed with a specified time are rejected from the scheme and, if able, are left to perform traditional synchronising after the majority of sets have become available. to minimise the paralleling start sequence time and get the gen-set system up and running with minimum possible delay
• Dynamic spinning reserve Dynamic Spinning Reserve allows the system to react flexibly to changes in power produced by renewable energy sources. ComAp controllers can react to requested spinning reserve and keep the sufficient amount of gen-sets running to cover the drop-in output of the renewable source (e.g. when cloud cover is heavier).preventing supply drops in hybrid installations with PVs
• Faster and cost-effective operations with signal sharing over a CAN bus across a group of control units
• Possibility to have a mains application in a gen-set controller with firmware upload functions
• Event-based history for fast and easy troubleshooting
• Automatic Mains Failure that ensures automatic start of gen-sets and minimises downtime
• Peak shaving for limiting the import from the mains (e.g. due to higher prices)
• Load shedding ensuring the most important loads are running even when there is a lack of power
• Compatible with the following remote displays:
  • InteliVision 5
  • InteliVision 8
  • InteliVision 12Touch

 * Feature available with a software key.

InteliSys NTC BaseBox GeCon Marine

The InteliSys NTC BaseBox GeCon Marine offers:

• Main functions: AMF function, Baseload, Import / Export, Peak shaving, Voltage and PF control (AVR)
• Easily configurable analogue and binary I/Os to suit every application requirement and adjust the number of expansion models used to optimise operations and costs
• Support for both ECU and mechanical engines
• Comprehensive overview of all measured data
• Event-based history for easy troubleshooting and performance analysis
• Intuitive and secure local and remote monitoring with a range of ComAp displays, PC tools and web-based services  
• Easy and cost-effective operations with signal sharing over a CAN bus
• Broad communication capabilities including Ethernet connection (RJ45), USB 2.0, RS232/ RS485 interface with Modbus protocol support; Analog / GSM / ISDN / CDMA modem communication support; SMS messages; ECU Modbus interface; isolated secondary RS485 
• AirGate 2.0 technology for easy connection to your equipment remotely, without worrying for about your asset’s IP address
• Automatic synchronisation and power control via speed governor or ECU
• Measurement of both generator and mains side
• Configurable inputs and outputs enabling customers to design functions according to their various needs
• Bi-polar binary outputs
• Controller redundancy minimising solution downtime and ensuring the power isn’t compromised
• Integrated PLC programmable functions
• Embedded fixed and configurable generator protection
• Easy customisation of the firmware solution according to your requirements
• Recommended to use with external colour displays InteliVision 8 or Intelivistion 5
• The controller has been certified by the following marine organisations: DNV, LR, ABS, BV, RINA, CRS, CCS 

 To run the GeCon software you need to order InteliSys NTC BaseBox and then install the correct GeCon software:

• GeCon LandBased (included in standard firmware)
• GeCon Marine (special dedicated marine firmware)
•  IGS-NT-LSM+PMS dongle (required for Load sharing and Power Management)